marvell yukon 88E8040不能联通

[junfengfan]

我有一台笔记本电脑，dell500n系列，有线网卡为marvell yukon 88E8040 pci-e fast ethernet controller；无线网卡为intel 3945ABG.
我通过路由器用网线连接到笔记本有线网卡marvell,而我在装openbsd4.9时网卡设定为192.168.0.101，子网255.255.255.0，网关192.168.0.1，DNS 202.102.224.68，可是就是不能上网，也不能ping 通192.168.0.1 ，其中偶然有一次出现可以上网，可是重启后又不能上网了，不知什么原因？

我从网上看到可以把openbsd装到笔记本上，而我又有一台笔记本，所以装了双系统，其中winxp可以正常用marvell yukon那块网卡上网，准备再装个gnome,试试看效果如何，可是却出现openbsd不能联通网络，既是局域网的别的机器也ping 不通，因为英文看不懂，还请您们帮助！

[leo]

英文看不懂指的是什么？
用DHCP直接获取IP地址试试—— /etc/hestname.接口名 这个文件的内容设置为

代码: 全选

dhcp

，此外贴出 ifconfig 命令的输出结果。

[lionux]

看看openbsd的网卡设置与路由是否一致。

[junfengfan]

我选用dhcp后可以联通，但当我用 fdisk -e sd0,f 0,quit
激活winxp后系统，再把openbsd.pdr放在winxp的C盘根目录下……当出现双启动菜单后，从openbsd49启动后，却还是不能上网！

[leo]

贴非DHCP配置时的网络接口配置文件内容，贴ifocnfig-a和ping的结果，请注意上面回帖的提问内容。

[junfengfan]

OpenBSD 4.9 (GENERIC) #671: Wed Mar 2 07:09:00 MST 2011
[email protected]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel(R) Celeron(R) CPU 550 @ 2.00GHz ("GenuineIntel" 686-class) 2 GHz
cpu0: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,TM,SBF,SSE3,MWAIT,DS-CPL,TM2,SSSE3,CX16,xTPR,PDCM
real mem = 1063272448 (1014MB)
avail mem = 1035747328 (987MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 10/16/08, BIOS32 rev. 0 @ 0xffa10, SMBIOS rev. 2.4 @ 0xf7190 (45 entries)
bios0: vendor Dell Inc. version "A16" date 10/16/2008
bios0: Dell Inc. Inspiron 1525
acpi0 at bios0: rev 2
acpi0: sleep states S0 S3 S4 S5
acpi0: tables DSDT FACP HPET APIC MCFG SLIC OSFR BOOT SSDT SSDT
acpi0: wakeup devices PCI0(S5) PCIE(S4) USB1(S3) USB2(S3) USB3(S3) USB4(S3) USB5(S3) EHC2(S3) EHCI(S3) AZAL(S3) RP01(S5) RP02(S3) RP03(S3) RP04(S3) RP05(S3) RP06(S3) LID_(S3) PBTN(S4) MBTN(S5)
acpitimer0 at acpi0: 3579545 Hz, 24 bits
acpihpet0 at acpi0: 14318179 Hz
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: apic clock running at 133MHz
ioapic0 at mainbus0: apid 1 pa 0xfec00000, version 20, 24 pins
ioapic0: misconfigured as apic 0, remapped to apid 1
acpimcfg0 at acpi0 addr 0xf8000000, bus 0-63
acpiprt0 at acpi0: bus 2 (PCIE)
acpiprt1 at acpi0: bus 9 (RP01)
acpiprt2 at acpi0: bus 11 (RP02)
acpiprt3 at acpi0: bus -1 (RP03)
acpiprt4 at acpi0: bus -1 (RP04)
acpiprt5 at acpi0: bus 12 (RP05)
acpiprt6 at acpi0: bus -1 (RP06)
acpiprt7 at acpi0: bus 0 (PCI0)
acpicpu0 at acpi0: C3, C2, C1
acpitz0 at acpi0: critical temperature 98 degC
acpibtn0 at acpi0: LID_
acpibtn1 at acpi0: PBTN
acpibtn2 at acpi0: SBTN
acpiac0 at acpi0: AC unit online
acpibat0 at acpi0: BAT0 model "DELL XR6828" serial 2859 type LION
acpivideo0 at acpi0: VID_
acpivout0 at acpivideo0: TV__
acpivout1 at acpivideo0: CRT_
acpivout2 at acpivideo0: LCD_
acpivout3 at acpivideo0: DVI_
acpivideo1 at acpi0: VID2
bios0: ROM list: 0xc0000/0xf000! 0xcf000/0x1000
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "Intel GM965 Host" rev 0x0c
vga1 at pci0 dev 2 function 0 "Intel GM965 Video" rev 0x0c
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
intagp0 at vga1
agp0 at intagp0: aperture at 0xe0000000, size 0x10000000
inteldrm0 at vga1: apic 1 int 16 (irq 11)
drm0 at inteldrm0
"Intel GM965 Video" rev 0x0c at pci0 dev 2 function 1 not configured
uhci0 at pci0 dev 26 function 0 "Intel 82801H USB" rev 0x02: apic 1 int 20 (irq 10)
uhci1 at pci0 dev 26 function 1 "Intel 82801H USB" rev 0x02: apic 1 int 21 (irq 9)
ehci0 at pci0 dev 26 function 7 "Intel 82801H USB" rev 0x02: apic 1 int 22 (irq 7)
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1
azalia0 at pci0 dev 27 function 0 "Intel 82801H HD Audio" rev 0x02: apic 1 int 21 (irq 9)
azalia0: codecs: Conexant/0x2c06, Sigmatel STAC9228X, using Sigmatel STAC9228X
audio0 at azalia0
ppb0 at pci0 dev 28 function 0 "Intel 82801H PCIE" rev 0x02: apic 1 int 16 (irq 0)
pci1 at ppb0 bus 9
mskc0 at pci1 dev 0 function 0 "Marvell Yukon 88E8040" rev 0x12, Yukon-2 FE+ rev. A0 (0x0): apic 1 int 16 (irq 11)
msk0 at mskc0 port A: address 00:21:9b:cf:3a:ab
eephy0 at msk0 phy 0: 88E3016 10/100 PHY, rev. 0
ppb1 at pci0 dev 28 function 1 "Intel 82801H PCIE" rev 0x02: apic 1 int 17 (irq 0)
pci2 at ppb1 bus 11
wpi0 at pci2 dev 0 function 0 "Intel PRO/Wireless 3945ABG" rev 0x02: apic 1 int 17 (irq 11), RoW, address 00:1f:3c:6b:64:0c
ppb2 at pci0 dev 28 function 4 "Intel 82801H PCIE" rev 0x02: apic 1 int 16 (irq 0)
pci3 at ppb2 bus 12
uhci2 at pci0 dev 29 function 0 "Intel 82801H USB" rev 0x02: apic 1 int 20 (irq 10)
uhci3 at pci0 dev 29 function 1 "Intel 82801H USB" rev 0x02: apic 1 int 21 (irq 9)
uhci4 at pci0 dev 29 function 2 "Intel 82801H USB" rev 0x02: apic 1 int 22 (irq 7)
ehci1 at pci0 dev 29 function 7 "Intel 82801H USB" rev 0x02: apic 1 int 20 (irq 10)
usb1 at ehci1: USB revision 2.0
uhub1 at usb1 "Intel EHCI root hub" rev 2.00/1.00 addr 1
ppb3 at pci0 dev 30 function 0 "Intel 82801BAM Hub-to-PCI" rev 0xf2
pci4 at ppb3 bus 2
"Ricoh 5C832 Firewire" rev 0x05 at pci4 dev 9 function 0 not configured
sdhc0 at pci4 dev 9 function 1 "Ricoh 5C822 SD/MMC" rev 0x22: apic 1 int 18 (irq 5)
sdmmc0 at sdhc0
"Ricoh 5C843 MMC" rev 0x12 at pci4 dev 9 function 2 not configured
"Ricoh 5C592 Memory Stick" rev 0x12 at pci4 dev 9 function 3 not configured
"Ricoh 5C852 xD" rev 0x12 at pci4 dev 9 function 4 not configured
ichpcib0 at pci0 dev 31 function 0 "Intel 82801HBM LPC" rev 0x02: PM disabled
pciide0 at pci0 dev 31 function 1 "Intel 82801HBM IDE" rev 0x02: DMA, channel 0 configured to compatibility, channel 1 configured to compatibility
atapiscsi0 at pciide0 channel 0 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <SONY, CDRWDVD CRX880A, KD09> ATAPI 5/cdrom removable
cd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
pciide0: channel 1 ignored (disabled)
ahci0 at pci0 dev 31 function 2 "Intel 82801HBM AHCI" rev 0x02: apic 1 int 17 (irq 10), AHCI 1.1
ahci0: PHY offline on port 2
scsibus1 at ahci0: 32 targets
sd0 at scsibus1 targ 0 lun 0: <ATA, Hitachi HTS54251, BB2O> SCSI3 0/direct fixed
sd0: 114473MB, 512 bytes/sec, 234441648 sec total
ichiic0 at pci0 dev 31 function 3 "Intel 82801H SMBus" rev 0x02: apic 1 int 17 (irq 10)
iic0 at ichiic0
spdmem0 at iic0 addr 0x50: 512MB DDR2 SDRAM non-parity PC2-5300CL5 SO-DIMM
spdmem1 at iic0 addr 0x52: 512MB DDR2 SDRAM non-parity PC2-5300CL5 SO-DIMM
usb2 at uhci0: USB revision 1.0
uhub2 at usb2 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb3 at uhci1: USB revision 1.0
uhub3 at usb3 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb4 at uhci2: USB revision 1.0
uhub4 at usb4 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb5 at uhci3: USB revision 1.0
uhub5 at usb5 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb6 at uhci4: USB revision 1.0
uhub6 at usb6 "Intel UHCI root hub" rev 1.00/1.00 addr 1
isa0 at ichpcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
mtrr: Pentium Pro MTRR support
uhub7 at uhub6 port 2 "Broadcom BCM2045B2" rev 2.00/1.00 addr 2
ugen0 at uhub7 port 1 "Broadcom Corp BCM2045" rev 2.00/3.67 addr 3
uhidev0 at uhub7 port 2 configuration 1 interface 0 "Broadcom product 0x4502" rev 2.00/1.00 addr 4
uhidev0: iclass 3/1
ukbd0 at uhidev0: 8 modifier keys, 6 key codes
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay0
uhidev1 at uhub7 port 3 configuration 1 interface 0 "Broadcom product 0x4503" rev 2.00/1.00 addr 5
uhidev1: iclass 3/1, 125 report ids
ums0 at uhidev1 reportid 2: 3 buttons
wsmouse1 at ums0 mux 0
uhid0 at uhidev1 reportid 125: input=2, output=0, feature=0
vscsi0 at root
scsibus2 at vscsi0: 256 targets
softraid0 at root
root on sd0a swap on sd0b dump on sd0b

[junfengfan]

lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 33200
priority: 0
groups: lo
inet 127.0.0.1 netmask 0xff000000
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x4
msk0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
lladdr 00:21:9b:cf:3a:ab
priority: 0
groups: egress
media: Ethernet autoselect (100baseTX full-duplex,rxpause,txpause)
status: active
inet 192.168.0.11 netmask 0xffffff00 broadcast 192.168.0.255
inet6 fe80::221:9bff:fecf:3aab%msk0 prefixlen 64 scopeid 0x1
wpi0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
lladdr 00:1f:3c:6b:64:0c
priority: 4
groups: wlan
media: IEEE802.11 autoselect
status: no network
ieee80211: nwid ""
enc0: flags=0<>
priority: 0
groups: enc
status: active
pflog0: flags=141<UP,RUNNING,PROMISC> mtu 33200
priority: 0
groups: pflog

[leo]

我分析，如果你使用DHCP可以联网，肯定是自己设置IP地址或网关什么的有误。
从这两个文件看不出毛病来，现在的IP地址192.168.0.11是通过DHCP服务器分配的吗？如果不是，也就是说是你自己设置的IP地址，说一下都设置了那些文件?
换句话说提供：

代码: 全选

# cat /etc/hostname.msk0
# cat /etc/mygate
# cat /etc/resolv.conf
# cat /etc/myname
# cat /etc/dhcpd.conf

如果自己发现了问题所在，修改完直接：

代码: 全选

# sh /etc/netstart

[junfengfan]

winxp机子关机，然后重新启动就可以上网了；强调的是如果你正在用winxp，请把机器关掉，断电后；然后再开机选openbsd进入，就可以上网了，有点意思~~~